Newspaper article from our research archive:
|
|
Solid carbide cutters mill aluminium faster.(CUTTING TOOLS)
- Article from:
-
Advanced Ceramics Report
- Article date:
-
February 1, 2007
|
Copyright informationCOPYRIGHT 2007 International Newsletters. This material is published under license from the publisher through the Gale Group, Farmington Hills, Michigan. All inquiries regarding rights should be directed to the Gale Group. (Hide copyright information)
|
WNT (UK) Ltd has introduced solid carbide cutters that have higher cutting speeds and feeds for machining aluminium than conventional tools.
The cutters (the 93033 series) range in size from 3 to 20 mm diameter and feature a single grind geometry with no relief angle. This provides a sharp, stable cutting edge, delivering much higher machining speeds and feeds than conventional cutters, the company says.
The improved performance is also helped by the specially designed geometry and helical angle, which enhances swarf evacuation.
Due to the strength of their ...
Related newspaper, magazine, and journal articles:
|
High-speed laser cutting.(laser cutting)
Production Technology News;
September 1, 2003 ;
95 words
......designed to take maximum advantage of enhanced cutting speeds through the use of the newest generation of laser...divergence Rofin SLAB Series laser helps attain cutting speeds up to 11,800 IPM in X-Y axes. System cuts maximum...
|
|
A short course in cast-iron turning
Manufacturing Engineering;
September 1, 1997 ;
700+ words
......prone to builtup edge (BUE) at low cutting speeds. In another case, harder, less ductile...short chipping and prone to BUE at low cutting speeds. When machining, the inserts are also...wear. The remedies are to run at high cutting speeds and flush the workpiece with abundant...
|
|
High-speed vitrectomy cutter provides greater precision
Ophthalmology Times;
February 1, 2000 ;
663 words
......instruments that could attain higher cutting speeds. The Millennium is what we've come...unable to keep up with attempted higher cutting speeds, problems arise." As the cut rate is...precision is attainable with higher cutting speeds and smaller bites," said Eugene de...
|
|
|
Machining nickel-based superalloys
Manufacturing Engineering;
March 1, 1999 ;
700+ words
......used to machine them at relatively low cutting speeds. The usual range of turning speeds...carbides, they can be used at higher cutting speeds, with distinctively reduced production...reinforced cutting ceramics and the higher cutting speeds which can be used. These advantages...
|
|
|
Choosing the right milling grade
Manufacturing Engineering;
January 1, 2001 ;
700+ words
......high edge security at moderate to high cutting speeds. Because toughness-optimized inserts...milling of harder steels at higher cutting speeds and moderate feed rates. Because it...steel hardened to Rc 60, or when high cutting speeds are used with general steels. When...
|
|
Cutting materials.
Industrial Distribution;
October 1, 2007 ;
96 words
......Two new grades, WPP01 and WPP05, provide efficiency at top cutting speeds with good machining results. A special carbide substrate...machining operations and roughing and is effective at top cutting speeds and stock removal rates. Walter USA www.walter-tools.com
|
|
Laser Cuts Stainless Steel With Speed.(Brief Article)(Product...
Welding Design & Fabrication;
June 1, 2001 ;
144 words
......edges whether cutting thin or thick stainless steel. Proven cutting speeds are 500 in./min. in 1/16, 82 in./min. in 5/16, and 10 in...controls and ability to cut with lower flow rates produces the cutting speeds while consuming approximately 30 percent less nitrogen assist...
|
 "The Birmingham Post (England)")
|
MOTORSPORT: FORMULA ONE: Cutting speeds.(Sport)
The Birmingham Post (England);
July 17, 2004 ;
86 words
...FIA president Max Mosley considers cutting speeds to be the main challenge facing him before his spell in office ends in October 2005 and the Englishman said last month that fear...
|
|
New kid on the block.
Precision Toolmaker;
November 1, 2000 ;
180 words
......characteristics such as an increase in tool life and higher cutting speeds. Sandvik Steel says that this new generation offers better machine utilisation through improved cutting speeds and feed rates plus more pieces per cutting tool. Potential...
|
|
|
TECHNOLOGY CUTS CYCLE TIME
Manufacturing Engineering;
January 1, 2006 ;
700+ words
......technology products that increase tool life, and improve cutting speeds and feeds, while addressing the critical need to reduce...Seco-Carboloy, Warren, MI) are used for all milling operations at cutting speeds from 50 to 70 m/min. Seco's CrownLoc Geometry M drills with...
|
|
|
Waterjet system intensifier.(new products)
Production Technology News;
August 1, 2004 ;
76 words
...The SL-V Plus 60,000 psi waterjet intensifier increases cutting speeds by up to 20% while maintaining excellent edge quality. It is extremely ergonomic and utilizes the Hyperlife plunger seal and ceramic...
|
|
Encore X-treme.(PRODUCT: RIDING MOWERS)
PRO Magazine;
June 22, 2006 ;
92 words
...Deck sizes: 48 , 52 , 60 Engines: 19-25 hp Productivity & performance * Cutting speeds up to 11 mph and blade tip speeds up to 19,000 fpm * Mulching kit, grass collection system and new striping kit available Durability...
|
|
Bosch SpeedWave diamond blades.(Product & Literature Guide)
Stone World;
August 1, 2007 ;
85 words
......reduces blade friction and drag. The design helps clear material and dust faster for better overall performance and faster cutting speeds. The world's first-ever center Cooling Disc draws in air and evenly cools the blade surface for longer life. SpeedWave utilizes...
|
See all results.
Or, try our
Advanced Search.
|