Articles > Government magazines > Applied and Social Sciences magazines > Metallurgical and Materials Transactions articles > August 1999

Article: Stress-Induced products in a Ti-14.8 V alloy deformed in tension

Article from:
Metallurgical and Materials Transactions
Article date:
August 1, 1999
Author:
Copyright

Beta titanium alloys are technologically important. Many properties of these materials such as ductility and ambient temperature creep behavior depend on the deformation mechanisms, which in turn depend on the microstructures. There has been significant controversy in regard to deformation mechanisms and stress-induced transformation products in metastable beta titanium alloys. In this investigation, the controversial views are briefly reviewed and compared with the results of the authors on the stress-induced transformation products in a Ti 14.8 wt pct vanadium alloy.

Stress-induced transformation products in a metastable beta titanium alloy with similar vanadium contents of approximately ...

Read all of this article with a FREE trial

Related newspaper, magazine, and journal articles:

Article: A fine gamma' + alpha cellular structure in Fe-37.3 Wt ...
Metallurgical and Materials Transactions;  June 1, 1999 ;     700+ words ... ... pct Ni-3.6 wt pct Al-3.3 wt pct Ti-0.2 wt pct C alloy, which reveals ... wt pct Ni3.6 wt pct Al-3.3 wt pct Ti-0.2 wt pct C on aging at 823 ... pct Ni-3.6 wt pct Al-3.3 wt pct ...

Article: Microstructure and Yield Strength of UDIMET 720LI Alloyed with ...
Metallurgical and Materials Transactions;  November 1, 2005 ;     700+ words ... ... with a two-phase alloy Co-16.9 wt pct Ti in various contents. The microstructure ... with the addition of Co-16.9 wt pct Ti, and its volume fraction increased ... increase in the addition of Co-16.9 wt pct Ti. The results of exposure at 750 ...

Article: The cellular interlamellar and growth-front interphase boundaries ...
Metallurgical and Materials Transactions;  August 1, 2002 ;     700+ words ... ... front interphase boundaries in Cu-3 wt pct Ti reveals an influence of crystallography ... complex defect networks. In Cu-3 wt pct Ti (all compositions are in weight ... EXPERIMENTAL PROCEDURE The Cu-3 wt pct Ti alloy was cast from Cu shot (99 ...

Article: Analysis of the Cu-3 Wt Pct Ti cellular ...
Metallurgical and Materials Transactions;  August 1, 2002 ;     700+ words ... ... interlamellar interface in Cu-3 wt pct Ti is modeled employing three different ... matrix, and beta is the Cu^sub 4^Ti orthorhombic phase. Probable defect ... equilibrium precipitate phase in Cu-3 wt pct Ti has a Cu^sub 4^Ti composition ...

Article: The Effects of Stress Level and Grain Size on the Ambient ...
Metallurgical and Materials Transactions;  March 1, 2005 ;     700+ words ... ... been carried out on an α-Ti-1.6 wt pct V alloy to determine the effects of ... investigated the phenomenon of creep in Ti-6A1-4V, a near α-titanium ... Odegaard[8] have also studied creep in Ti-5Al-2.5Sn (Ti-5-2.5 ...

Article: Microstructure Characterization and Creep Deformation of an Al-10 ...
Metallurgical and Materials Transactions;  December 1, 2004 ;     700+ words ... ... particles are likely to be Al^sub 3^Ti. I. INTRODUCTION MANY recent articles ... current article, we study an Al-IO wt pet Ti-2 wt pet Cu nanocomposite produced by ... cryomilled and consolidated Al-IO wt pet Ti-2 wt pet Cu is investigated at temperatures ...

Article: Effect of Phosphorus and Strontium Additions on Formation ...
Metallurgical and Materials Transactions;  July 1, 2009 ;     700+ words ... ... nucleation density of primary silicon in Al-19 wt pct Si alloy has been determined, for small ... sup 1/2^ 10^sup 9^ [250 - 215 (wt pct P)^sup 0.17^]^sup -3^, where ... Song et al.[13] reported that 0.02 wt pct P raised the primary silicon start temperature ...

Article: Relationship between austenite dislocation density introduced ...
Metallurgical and Materials Transactions;  July 1, 2002 ;     700+ words ... ... M^subS^) temperature of an Fe-17 wt pct Mn alloy was quantitatively investigated ... that the austenite hardness of an Fe-25 wt pct Mn alloy, which was measured at 573 K ... cycles between 303 and 573 K in an Fe-17 wt pct Mn alloy. The objective of their study ...

 
 
Newsweek Harper's Magazine The Washington Post Chicago Tribune Crain's Chicago Business PRNewswire Pediatric News The Nation Advertising Age The Economist (US) A FREE trial gives you access to over 80 million articles! Access over 6,500 publications with a FREE trial!

Find articles, research, and archives